Premier Mounts Projector Accessories GB PIPE1 User Manual

INSTALLATION INSTRUCTIONS  
GB-PIPE1/GB-PIPE1B  
Pipe-Mounted Equipment Enclosure  
AUSTRALIA, NEW ZEALAND, OCEANIA  
EUROPE  
Swallow House,  
NORTH AMERICA  
3130 East Miraloma Avenue  
Anaheim, CA 92806 USA  
USA and Canada –  
(DISTRIBUTOR)  
P.O. Box 295  
Shilton Industrial Estate,  
Shilton, Coventry, England CV79JY  
Phone: +44 (0) 2476 614700  
Fax: +44 (0) 2476 614710  
Mordialloc Victoria 3195  
Australia  
Phone: 039586 6330  
Phone: 800-368-9700  
Fax: 800-832-4888  
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044  
©Premier Mounts 2008  
9534-004-003-00  
 
GB-PIPE1  
Parts List  
This accessory is shipped with all proper installation hardware and components. Make sure that none of these parts  
are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the  
installation and contact Premier Mounts (800-368-9700).  
Equipment Tray (Qty 1)  
Side Panel (Qty 2)  
Upper Plate (Qty 1)  
M5 x 10mm Security Head Screw (Qty4)  
M4 x 8mm Security Head Screw (Qty 10)  
M8 x 12mm Security Head Screw (Qty8)  
Installation Tools  
M5 Security Wrench  
M3 Security Wrench  
Installation Instructions  
Page 3  
 
GB-PIPE1  
GB-PIPE1 Installation  
The GB-PIPE1 is designed for use with either a standard piece of 1-1/2” NPT pipe or any available ceiling mount adapter  
from Premier Mounts. Please refer to the ceiling mount adapter installation instructions when mounting.  
Unpack the Gear Box and review any WARNING statements that apply to the installation. Select the desired location for  
the GB-PIPE1.  
1-1/2” NPT  
Set Screw  
M3 Security  
Wrench  
Upper Plate  
Step 1. Determine where the GB-PIPE1 will be  
Step 4. Use an M3 security wrench to tighten the  
located.  
set screw.  
Step 2. Install your 1-1/2” NPT or ceiling adapter.  
Step 3. Attach the upper plate to the NPT or  
adapter by rotating counter-clockwise.  
The upper plate must rotate onto the  
threads at least four (4) complete  
rotations.  
Pipe  
Electronic  
Component  
Cables  
Step 5. At this time, run all existing cables through  
the pipe and down through the upper  
plate.  
At this time, you may pre-install your  
electronic components in the equipment  
tray.  
Page 4  
Installation Instructions  
 
GB-PIPE1  
M4 x 10mm  
Security  
Screws  
Upper Plate  
Spring Loaded  
Nuts  
Electronic Components  
Mounting Hole  
Step 7. Line up the mounting holes with the  
threaded shaft of the spring loaded nuts.  
Step 6. Lift the equipment tray into position.  
Step 8. Once the holes are lined up, press down  
on the spring loaded nuts and tighten.  
Step 9. Insert and tighten two (2) M4 x 10mm  
security screws on the upper plate.  
1-1/2” NPT Installation  
Before attaching the lower 1-1/2” NPT, it is strongly recommended that all connections in the equipment tray be made at  
this time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please  
read instructions below to complete the installation.  
1-1/2” NPT  
Equipment Tray  
Plate Hole  
Set Screw  
1-1/2” NPT  
Step 1. Place the threaded end of the 1-1/2” NPT  
Step 2. Use an M3 security wrench to tighten the  
set screw.  
into the plate hole.  
Step 3. Attach projector mount to NPT.  
The NPT must rotate onto the  
equipment tray four (4) complete  
rotations.  
Please follow the instructions  
included with the mount to complete  
this step. If using a PDS Series mount,  
connection may be made directly to  
the bottom of the equipment tray.  
Installation Instructions  
Page 5  
 
GB-PIPE1  
PDS-PLUS Installation without NPT (Optional)  
Before attaching the PDS-PLUS, it is strongly recommended that all connections in the equipment tray be made at this  
time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please read  
instructions below to complete the installation.  
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.  
Mounting Slots  
Equipment  
Tray  
M8 x 12mm  
Security Head  
Screw  
M5 Security  
Wrench  
Base Box  
Bridge  
Step 1. Remove the lower mounting plate from  
the equipment tray by removing the four  
(4) M8 x 12mm security head screws with  
an M5 security wrench.  
Step 2. Locate the mounting slots that are on the  
base box bridge of the PDS-PLUS.  
Mounting  
Point  
Equipment  
Tray  
Equipment  
Tray  
Base Box  
Bridge  
Base Box  
Bridge  
M5 x 10mm  
Security Head  
Screw  
M5 Security  
Wrench  
M5 Security  
Wrench  
M5 x 10mm  
Security Head  
Screw  
Step 3. Line up the mounting slots on the base box  
bridge with the mounting points on the  
equipment tray.  
Step 4. Insert four (4) M5 x 10mm security screws  
and tighten using the M5 security wrench.  
Be aware of the screen location and  
orient the base accordingly.  
Page 6  
Installation Instructions  
 
GB-PIPE1  
Cable Connections  
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.  
Equipment  
Tray  
PDS-PLUS  
Base Box  
Cables  
Cables  
Step 1. Pull all cables down through the  
Step 2. Pull all cables down through the  
PDS-PLUS projector plate.  
PDS-PLUS base box.  
Step 3. Attach all cables to the installed  
projector.  
Side Panel Installation  
M4 x 8mm  
Security Screw  
Side Panel  
Side Panel  
M3 Security  
Wrench  
Side Panel  
Step 2. Tighten these screws using the M5  
Step 1. Attach the two side panels using eight (8)  
security wrench.  
M4 x 8mm security screws.  
Installation Instructions  
Page 7  
 
GB-PIPE1  
Lateral Shift Adjustment  
M5 Security  
Wrench  
M8 x 12mm  
Security Head  
Screw  
Step 1. Use the M5 security wrench and loosen  
Step 2. Once the screws have been loosened,  
slide the GB-PIPE1 laterally side to side  
(or front to back).  
Step 3. When the desired position has been  
determined, use the M5 security wrench to  
tighten the M8 x 12mm security screws.  
the four (4) M8 x 12mm security screws.  
Do not completely remove these screws.  
Technical Specifications  
All measurements are in inches(mm).  
Page 8  
Installation Instructions  
 
GB-PIPE1  
Warranty  
PREMIER MOUNTS  
LIMITED LIFETIME WARRANTY  
What and Who is Covered by this Limited Warranty and for How Long  
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of  
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.  
What Premier Mounts Will Do  
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is  
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will  
be shipped to you at no charge, but you must pay any labor costs.  
What is Not Covered; Limitations  
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-  
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN  
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.  
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER  
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-  
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-  
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE  
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE  
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.  
What Customers Must Do for Limited Warranty Service  
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to  
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-  
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the  
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier  
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.  
Premier Mounts  
Attn: Warranty Claim  
3130 East Miraloma Ave.  
Anaheim, CA 92806  
How State Law Applies  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER  
RIGHTS WHICH VARY FROM STATE TO STATE.  
Installation Instructions  
Page 9  
 

Peerless Industries TV Mount HP450 User Manual
Philips Digital Photo Frame SPF5208 12 User Manual
Philips Projector PMU50 User Manual
Philips Security Camera BB HCA10CE User Manual
Philips Work Light P 5775 B User Manual
Pioneer DVD Recorder DVR TS08 User Manual
Pioneer Flat Panel Television PRO 920HD User Manual
Planet Technology Switch FSD 805S15 User Manual
Precisionaire Air Cleaner Series 225T Cube User Manual
ProScan Refrigerator FRW041 User Manual