Premier Mounts Indoor Furnishings XUT 2637 User Manual

Included Hardware  
Griplates  
(Qty 8)  
3” Lag Bolts  
(Qty 6)  
INSTALLATION GUIDE: XUT-2637  
NOTE:  
To correctly determine your hardware,  
please refer to the hardware list below.  
Flat Washers (Qty 6)  
Victory Tilt Screen Wall Mounting System  
The Victory Tilt Screen Wall Mounting System is designed for secure installation of flat screen displays up  
to 42”.  
Warning Statements  
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A  
MINIMUM WEIGHT OF 250 LBS. IF NOT, THE WALL MUST BE REINFORCED.  
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN,  
AS OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.  
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN  
DEATH. DO NOT PLACE A UNIT WEIGHING MORE THAN 125LBS. ON THIS  
MOUNT  
WARNING:  
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE  
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS  
FOR THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.  
WARNING:  
WARNING:  
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION  
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE  
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL  
INJURY AND PROPERTY DAMAGE. KEEP THESE INSTALLATION  
INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE  
REFERENCE.  
Tool List  
Phillips Head Screw Driver  
Electronic Stud Finder  
½” Socket and Wrench  
Portable Drill  
A secure structure must support the weight, or load, of the display. When mounting to a  
wall that contains wooden studs, dead center of the wooden stud must be confirmed prior to  
installation.  
Masonry Bit for Concrete Installation  
1/4” Drill Bit for Wood Installations  
Level (Commercially Available)  
Do not install on a structure that is prone to vibration, movement or chance of impact.  
Failure to do so could result in damage to the display and/or damage to the mounting  
surface.  
Wood Stud Mounting  
1. For secure wood stud mounting, the wall plate must be  
mounted to two studs at least 16” apart.  
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of  
direct heat energy. Failure to do so may result in damage to the display and could increase  
the risk of fire.  
2. Use a high-quality electronic stud finder (commercially  
available) to locate two adjacent studs and mark their  
locations with a pencil.  
3. With the help of an assistant, use a level (commercially  
available) and position the wall plate against the wall in  
the desired mounting location.  
At least two qualified people should perform the installation procedure. Injury and/or  
damage can result from dropping or mishandling the display.  
4. Mark the right (upper and lower) and the left (upper  
and lower), positions of the small horizontal slots  
that are in alignment with the studs.  
5. You should mark four positions total.  
6. Next, pre-drill a 1/4” hole in the wall stud at each  
marked location.  
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to  
be installed on any surface other than wooden studs, use suitable hardware (which is  
commercially available).  
Lag Bolt and Washer  
Contact Victory Mounts with any technical / installation questions.  
Continued on back page  
9531-015-112-06  
 

Pelco Security Camera C1969M A User Manual
Pentax Carrying Case 300X User Manual
Pentax Webcam iqzoom60 User Manual
Philips Car Video System 100WT10P User Manual
Philips Electric Toothbrush HX3300 User Manual
Philips Portable Radio AE1506 04Z User Manual
Polar Fitness Electronics FT40TM User Manual
Polaroid Digital Camera 7500Zix User Manual
Proxima ASA Projector 5155SVGA User Manual
PYLE Audio Automobile Accessories PNVU200 User Manual