Premier Mounts Indoor Furnishings XUT 1330L User Manual

Included Hardware  
M4 x 12mm Phillips  
Head Screw  
(Qty 4)  
¾” Spacer (Qty 4)  
INSTALLATION GUIDE: XUT-1330L  
M4 x 30mm Phillips  
Head Screw  
(Qty 4)  
Victory LCD Wall Mounting System  
2” Wood Screw  
(Qty 2)  
The Victory LCD Mounting System is designed for secure installation of LCD displays of up to  
40 lbs. in weight.  
Bubble Level (Qty 1)  
Tool List  
Warning Statements  
Phillips Head Screw Driver  
Electronic Stud Finder  
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM  
WEIGHT OF 40 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER  
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN  
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO  
COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH.  
WARNING:  
Allen Wrenches (supplied)  
Portable Drill  
¼” Masonry Bit for Concrete Installation  
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION  
OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION  
PROCEDURE TO PREVENT PERSONAL INJURY.  
WARNING:  
WARNING:  
NOTE: The included level may be permanently  
attached to the wall plate by inserting the  
level into the receptacle on the back of the  
wall plate.  
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS  
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION  
INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY  
DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE  
LOCATION FOR FUTURE REFERENCE.  
Wood Stud Installation  
NOTE: Using  
a
wood stud finder, locate the  
stud centers behind the wall. Once found,  
make a pencil marking on the center of the  
wood studs. Once the mark is made, it is  
strongly recommended that a pilot hole be  
drilled with a 1/8” drill bit.  
A secure structure must support the weight or load of the display. When mounting to a wall that  
contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.  
1. Place the back plate against the wall with the  
hook towards the bottom.  
2. Secure the back plate using one (1) 2” wood  
screw.  
3. Using the integrated bubble guide, carefully  
adjust the back plate until it is level.  
4. Attach the remaining 2” wood screw into the back  
plate and tighten.  
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to  
do so could result in damage to the display and/or damage to the mounting surface.  
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct  
heat energy. Failure to do so may result in damage to the display and could increase the risk of  
fire.  
At least two qualified people should perform the installation procedure. Injury and/or damage  
can result from dropping or mishandling the display.  
Concrete Installation  
NOTE: ¼” x 2 ¼” Threshold anchors must be used  
for concrete installation. They can be  
purchased at your local hardware store.  
1. Place the back plate against the wall with the hook  
towards the bottom.  
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be  
installed on any surface other than wooden studs, use suitable hardware (which is  
commercially available).  
2. Level and mark with a pencil the two mounting  
points found on the back plate.  
Contact Victory Mounts with any technical / installation questions.  
3. Next, drill two holes using an electric drill and ¼”  
masonry bit.  
4. Insert the threshold anchors into the holes that  
were drilled in the wall.  
NOTE: If necessary, use a hammer to lightly tap  
each anchor into place so that they are  
flush with the wall. Once mounted in the  
wall, unscrew the slotted cap off of the  
threaded insert.  
Threshold  
Anchor  
5. Once the anchors are in place, set the back  
plate back over the concrete anchors.  
6. Using a Slot Head screw driver, attach the back  
plate by threading the two slotted caps onto the  
threaded insert that is recessed into the wall.  
7. Make sure all screws are snug, but be careful not  
to over-tighten them.  
Slotted Cap  
Threaded Insert  
Threshold Anchor  
 

Peavey Guitar Axcelerator 5 User Manual
Peavey Musical Instrument Amplifier 6505 User Manual
Pelco Car Video System PMCL400 Series User Manual
Philips Headphones SHS4848 28 User Manual
Philips Styling Iron HP9345 User Manual
Philips Work Light PAR30L User Manual
Plantronics Headphones 8005701 User Manual
Premier Mounts Modem CDM 600 User Manual
Proxima ASA Projector DP9270 User Manual
PS Audio Stereo System C 100 User Manual