Patton electronic Switch 4654 Series User Manual

SmartNode 4654 and 4658 Series  
ADSL2+ Multiport ISDN VoIP IAD  
Quick Start Guide  
Important—This is a Class A device and is intended for use in a light industrial environment. It is not  
intended nor approved for use in an industrial or residential environment.  
Approval—This device is approved for connection to the public ISDN telecommunication network,  
over BRI/S0-ISDN interfaces.  
Zulassung—Zugelassen für die Anschaltung an das öffentliche ISDN Telekommunikationnetz an  
BRI/S0-ISDN Schnittstellen.  
Aprobación—Este aparato está aprobado para conexión a red publica ISDN sobre interfaz BRI/S0.  
Approbation—Cet appareil est approuve pour la connexion au reseau ISDN public avec les interfaces  
BRI/S0.  
Document Number: 13225U7-002 Rev. A  
Part Number: 07MSN4650A-QS  
Revised: June 12, 2008  
Sales Office: +1 (301) 975-1000  
Technical Support: +1 (301) 975-1007  
 
+
1
2
V
,
1
.2  
5
A
C
A
T
L
IN  
K
Straight-through wired cable  
LAN (ETH 0/0)  
Laptop PC  
Figure 1. Connecting to the PC  
1. Connect the PC’s Ethernet port to LAN (ETH 0/0) port of the SmartNode 4650 ADSL2+. The SmartNode  
4650 ADSL2+ Series is equipped with Auto-MDX Ethernet ports, so you can use straight-through Ethernet  
cables for host or hub/switch connections. (See figure 1.)  
2. The SmartNode comes with a built-in DHCP server to simplify configuration. Therefore, to automatically  
configure the PC for IP connectivity to the SmartNode, configure the laptop PC for DHCP. The SmartNode  
will provide the PC with an IP address.  
3. Check the connection to the SmartNode by executing the ping command from the PC command window  
as follows:  
ping 192.168.1.1  
3.0 Configuring the desired IP address  
3.1 Factory-default IP settings  
The factory default configuration for the Ethernet interface IP addresses and netmasks are listed in table 1.  
Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP  
server. The WAN interface uses DHCP client to get the IP address and netmask automatically from the  
service provider.  
Table 1. Factory default IP address and network mask configuration  
Item  
IP Addresss  
Network Mask  
DHCP  
WAN interface DSL port (DSL 0/0)  
LAN interface Ethernet 1 (ETH 0/0)  
DHCP server address range (LAN)  
DHCP  
192.168.1.1  
255.255.255.0  
255.255.255.0  
192.168.1.10-192.168.1.19  
network” on page 4. Otherwise, continue with the following sections to change the addresses and  
network masks.  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
3
 
3.2 Login  
1. To access the SmartNode, start the Telnet application on your PC. Type the default IP address into the  
address field: 192.168.1.1. Accessing your SmartNode via a Telnet session displays the login screen.  
Type the factory default login: administrator and leave the password empty. Press the Enter key after the  
password prompt.  
login:administrator  
password:<Enter>  
192.168.1.1>  
2. After you log in, your SmartNode will be running in operator execution mode (indicated by > character  
in the command line prompt). To enter configuration mode, use the commands enable and configure.  
192.168.1.1>enable  
192.168.1.1#configure  
192.168.1.1(cfg)#  
3.3 Changing the WAN IP address  
1. To modify IP configuration settings, you must enter context IP mode. Enter the following command:  
192.168.1.1(cfg)#context ip router  
192.168.1.1(ctx-ip)[router]#  
2. Now you can set your IP address and network mask for the interface ETH 0/0(WAN). In this example a  
network 172.16.1.0/24 is assumed. The IP address in example is set to 172.16.1.99. (You should set it  
to the IP address that the network provider has given you.)  
Note The examples in this guide use a private IP network with the network address 172.16.1.0/24.  
192.168.1.1(ctx-ip)[router]#interface eth_dsl  
192.168.1.1(if-ip)[eth_dsl]#ipaddress 172.16.1.99 255.255.255.0  
2002-10-29T00:09:40 : LOGINFO  
2002-10-29T00:09:40 : LOGINFO  
172.16.1.99(if-ip)[eth_dsl]#  
: Link down on interface eth0.  
: Link up on interface eth0.  
3. Copy this modified configuration to your new start-up configuration. This will store your changes in non-  
volatile memory. On the next start-up the system will initialize itself using the modified configuration.  
172.16.1.99 (if-ip)[eth_dsl]#copy running-config startup-config  
172.16.1.99 (if-ip)[eth_dsl]#  
The SmartNode can now be connected to your network.  
4.0 Connecting the SmartNode to the network  
The interconnecting cables shall be acceptable for external use and shall be rated for  
the proper application with respect to voltage, current, anticipated temperature, flam-  
mability, and mechanical serviceability.  
CAUTION  
4
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
 
 
In general, the SmartNode will connect to the network via the WAN (DSL) port. This enables the SmartNode to  
offer routing services to the PC hosts on LAN (ETH 0/)) port. The SmartNode 4650 ADSL2+ Series provides an  
auto-MDX feature for both Ethernet ports, so you can use a straight-through or cross-over cable to connect to a  
host or a switch (see figure 2).  
12V  
,
1.25A  
A
C
T
L
IN  
K
LAN  
Straight-through wired  
or crossover cable  
LAN (ETH 0/0)  
Network  
WAN (DSL)  
Figure 2. Connecting the SmartNode to the network  
1. You can check the connection with the ping command from the SmartNode to another host on the  
local LAN.  
172.16.1.99(if-ip)[eth_dsl]#ping <IP Address of the host>  
Note If the WAN address is not set to DHCP, to ping a device outside your local LAN you must first configure  
the default gateway. (For information on configuring the default gateway, refer to section “Set IP  
addresses” in Appendix C, “Command Summary” of the SmartNode Series SmartWare Software Config-  
uration Guide.)  
5.0 Loading the configuration (optional)  
Patton provides a collection of configuration templates on the CD-ROM shipped with your SmartNode device—  
and also on the support page at www.patton.com/voip—one of which may be similar enough to your  
application that you can use it to speed up configuring the SmartNode. Simply download the configuration note  
that matches your application to your PC. Adapt the configuration as described in the configuration note to your  
network (remember to modify the IP address) and copy the modified configuration to a TFTP server. The Smart-  
Node can now load its configuration from this server.  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
5
 
you do not see your application on the CD-ROM, it may have been added to the website.  
Note If your application is unique and not covered by any of Patton’s configuration templates, you can man-  
ually configure the SmartNode instead of loading a configuration file template. In that case, refer to  
the SmartNode Series SmartWare Software Configuration Guide for information on configuring the Smart-  
Node device.  
In this example we assume an TFTP server resides on the host with the IP address 172.16.1.11 and the configu-  
ration file named SN.cfg resides in the root directory of the TFTP server.  
config  
Download...100%  
172.16.1.99(if-ip)[eth0]#  
After you reboot the SmartNode the new startup configuration will become active.  
When you issue the reload command, the SmartNode will ask if you want to copy the  
running configuration to the startup configuration. Since you just downloaded a con-  
figuration file to the startup configuration you must answer this question with NO.  
Otherwise, the downloaded configuration will be overwritten and lost!  
IMPORTANT  
172.16.1.99(if-ip)[eth0]#reload  
Running configuration has been changed.  
Do you want to copy the 'running-config' to the 'startup-config'?  
Press 'yes' to store, 'no' to drop changes : no  
Press 'yes' to restart, 'no' to cancel : yes  
The system is going down  
6.0 Additional Information  
Refer to the SmartNode Series SmartWare Software Configuration Guide and the SmartNode Getting Started Guide  
located on the CD-ROM shipped with your SmartNode device and available online at www.patton.com/  
manuals. For detailed information about:  
Installing, configuring, operating, and troubleshooting.  
Warranty, trademark & compliance  
The CD-ROM also includes many freeware and shareware tools, including TFTP servers, and Telnet clients.  
A.0 Customer and Technical Support  
Toll-Free VoIP support: call sip:[email protected] with a VoIP SIP client  
Online support: www.patton.com  
E-mail support: [email protected]—answered within 1 business day  
6
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
 
Telephone support:  
Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to  
2200 UTC/GMT)  
Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800  
UTC/GMT)  
Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)  
B.0 Compliance Information  
B.1 Compliance  
EMC Compliance:  
FCC Part 15, Class A  
EN55022, Class A  
EN55024  
Safety Compliance:  
UL60950-1/CSA C22.2 No. 60950-1  
IEC/EN 60950-1  
AS/NZS 60950-1  
PSTN Regulatory Compliance:  
TBR3  
AS/ACIF S031  
AS/ACIF S043 (ADSL card)  
B.2 Radio and TV interference  
The SmartNode router generates and uses radio frequency energy, and if not installed and used properly—that  
is, in strict accordance with the manufacturer’s instructions—may cause interference to radio and television  
reception. The SmartNode router have been tested and found to comply with the limits for a Class A computing  
device in accordance with specifications in Subpart B of Part 15 of FCC rules, which are designed to provide rea-  
sonable protection from such interference in a commercial installation. However, there is no guarantee that  
interference will not occur in a particular installation. If the SmartNode router does cause interference to radio or  
television reception, which can be determined by disconnecting the unit, the user is encouraged to try to correct  
the interference by one or more of the following measures: moving the computing equipment away from the  
receiver, re-orienting the receiving antenna and/or plugging the receiving equipment into a different AC outlet  
(such that the computing equipment and receiver are on different branches).  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
7
 
B.3 ISDN compliance  
This device is approved for connection to the public ISDN telecommunication network.  
When this device is used in North America, it shall be connected to a Network Termina-  
tion Device and not connected directly to an outside POTS line.  
CAUTION  
B.4 CE Declaration of Conformity  
Product Description: SmartNode 4650 ADSL2+ Series  
This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the laws  
of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual recognition  
of their conformity.  
The safety advice in the documentation accompanying the products shall be obeyed.  
The conformity to the above directive is indicated by the CE sign on the device.  
The signed Declaration of Conformity can be downloaded from www.patton.com/certifications/.  
B.5 EG-Konformitätserklärung  
Produktbezeichnung: SmartNode 4650 Sendereihe  
Die bezeichneten Produkte stimmen in der von uns in Verkehr gebrachten Ausführung mit den Vorschriften fol-  
gender Richtlinie überein:  
R&TTE 1999/5/EG  
Richtlinie des europäischen Parlaments und des Rates zur Angleichung der Rechtsvorschriften der Mitglied-  
staaten über Funkanlagen und Telekommunikations-Endeinrichtungen und die gegenseitige Anerkennung ihrer  
Konformität.  
Die Sicherheitshinweise in der mitgelieferten Produktdokumentation sind zu beachten.  
Die Konformität mit der oben erwähnten Richtlinie wird durch das CE-Zeichen auf dem  
Gerät bestätigt.  
Die unterzeichnete Konformitätserklärung kann heruntergeladen werden von: www.patton.com/  
certifications/.  
B.6 Zulassung  
Zugelassen fur die Anschaltung an das öffentliche ISDN Telekommunikationnetz an BRI/S0-ISDN Schnittstellen.  
B.7 Authorized European Representative  
D R M Green, European Compliance Services Limited.  
Oakdene House, Oak Road , Watchfield, Swindon, Wilts SN6 8TD, UK  
8
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
 
Copyright statement  
Copyright © 2008, Patton Electronics Company. All rights reserved.  
The information in this document is subject to change without notice. Patton Electronics assumes no  
liability for errors that may appear in this document.  
Trademarks statement  
The term SmartNode is a trademark of Patton Electronics Company. All other trademarks presented in this docu-  
ment are the property of their respective owners.  
Warranty, Trademark, & Compliance Information  
For warranty, trademark and compliance information, refer to the Models SN4650 Series Getting Started Guide  
located on the CD-ROM that came with your VoIP Gateway Router or available online at www.patton.com.  
In accordance with the requirements of council directive 2002/96/EC on Waste of  
Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate  
this product from other waste and scrap and deliver to the WEEE collection system in  
your country for recycling.  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
9
 
Notes  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
10  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
 
Notes  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
 
Notes  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
____________________________________________________________________  
12  
SmartNode 4654 & 4658 ADSL2+ Quick Start Guide  
 

Peavey Music Mixer AMD 1220 User Manual
Perreaux Power Supply SP100A User Manual
Philips Bottle Warmer SCF660 User Manual
Philips Computer Monitor 107X4 User Manual
Philips Fan HD 3274 75 User Manual
Philips Flat Panel Television 14PF7846 User Manual
Philips Power Supply LR14PB2C User Manual
Polaroid MP3 Player PMP283C 4 User Manual
Poulan Chainsaw Chainsaw User Manual
Powermatic Sander WB 25 User Manual